If you’re a dirt bike racer—whether you’re tearing up local motocross tracks, hitting backcountry desert trails, or pushing for podiums in amateur series—you know your bike’s rear suspension is non-negotiable. Too soft, and you’ll bottom out over triple jumps, get bucked loose on whoops, and lose precious traction when accelerating out of corners. Too stiff, and you’ll bone-jar over small ruts, fatigue after a 30-minute race, and sacrifice speed because your tire never stays planted to the ground. As a Racing Dirt Bike supplier, I’ve helped thousands of riders dial their rear suspension to match their weight, riding style, and track conditions, and today I’m breaking down the science and practical steps to do it right. Racing Dirt Bike

First, let’s cut through the jargon: rear suspension on a modern racing dirt bike uses two key adjustments: spring preload and rebound damping. There’s also compression damping, which is more often adjusted on the front forks, but we’re focusing on the rear because that’s where most riders get stuck. Let’s start with the basics: spring preload is how much you compress the shock spring at rest, and it’s tied directly to your weight. Rebound damping controls how fast the shock extends after it compresses over a bump, and it’s critical for keeping your tire on the ground between hits.
Let’s start with spring preload, because this is the foundation of your setup. If your preload is wrong, no amount of fine-tuning damping will fix your bike’s feel. The rule here is simple: your preload should be set so that when you’re sitting on the bike with full gear (riding gear, helmet, boots, the whole nine yards), the rear suspension compresses about 20 to 30 percent of its total travel. Wait, you can’t measure that? Easy: find the rear tire’s ground contact point, mark the swingarm’s pivot bolt with a piece of tape, and have a friend hold the bike upright. Sit on it, slowly shift your weight until you’re in your normal riding posture, then stand back and mark the pivot bolt again. The difference between the two marks is how much your suspension is compressing at rest. If that number is less than 20 percent, your spring is too soft—you’ll bottom out hard on big hits, even if you have preload cranked all the way up. If it’s more than 30 percent, your spring is too stiff—you’ll feel every tiny bump, and your tire won’t have enough travel to follow the track.
How do you adjust preload? Most modern racing dirt bikes have a preload adjuster ring at the top of the rear shock, near the shock body. Some are turnable by hand, others need a special spanner wrench (we stock these as part of our Racing Dirt Bike tool kits, by the way, no need to buy a generic one that won’t fit). Turning the ring clockwise increases preload, which makes the spring firmer. If your compression at rest is too high (over 30 percent), turn it counterclockwise to soften the spring and reduce preload. Pro tip: if you’re a 180-pound rider, you’ll need a stiffer spring than a 120-pound rider, even if you’re riding the same track. I see so many new riders skip checking their spring and just crank preload, which is a mistake—preload is for fine-tuning once you have the right spring for your weight, not a replacement for it.
Now, rebound damping. This is where the magic happens, and where most riders get it backwards. Let’s explain rebound in simple terms: when you hit a bump, the shock compresses (that’s the impact), and it needs to extend back out smoothly to be ready for the next bump. If rebound is too fast, the shock extends too quickly, lifting your tire off the ground mid-corner or mid-jump. If it’s too slow, the shock stays compressed, so the next bump hits the solid shock body instead of the spring, leading to harsh rides and lost traction.
Adjusting rebound depends on your riding style and the track. Let’s break it down for common scenarios:
First, flat, hard-packed motocross tracks with tight whoops and short jumps. These tracks require fast rebound, because whoops are a series of tiny, rapid hits—if your rebound is too slow, the shock won’t extend back fast enough to handle each successive whoop, and you’ll get bucked around. Most pro riders run rebound at around 5 to 8 clicks out from full slow (remember: most adjusters have the “full slow” position as the start, turning clockwise makes rebound faster, counterclockwise makes it slower—always double-check your bike’s manual, some brands label this the opposite). For flat tracks, start at 6 clicks out and test: if your front wheel is bouncing off the ground after a jump, go faster (more clicks). If you feel like the rear end is squatting too much on acceleration, go slower (fewer clicks).
Next, rough, rocky trails or desert tracks with big jumps and variable terrain. Here, you want slower rebound, because you need the shock to stay extended over big hits to maintain traction on uneven ground. If you have fast rebound here, the shock will extend too quickly after a big bump, leaving your tire hanging in the air when you need it most. For these tracks, start at 10 to 12 clicks out from full slow, and test: if your bike feels like it’s pitching forward over small bumps, go faster (less clicks). If the rear end feels like it’s hanging up after a landing, go slower (more clicks).
Wait, what about cornering? If you’re leaning into a turn, the rear suspension compresses on the outside, right? Rebound also affects how the bike handles in corners. If rebound is too fast, the rear end will lift as you exit a turn, making it hard to accelerate without spinning the tire. If it’s too slow, the rear end will stay compressed, leading to understeer or a “wallowy” feel mid-corner. That’s why testing is non-negotiable—don’t just set it once and forget it. Bring your bike to a small track or an empty field, do a few laps, and adjust one click at a time. Even a 1/16 of a turn can change the feel, so small adjustments are key.
Now, let’s talk about a common mistake: adjusting both preload and rebound at the same time. I see riders show up to the track, crank preload because they think their bike is “too low,” then twist rebound because the rear is bouncing, and end up with a setup that’s way off. Always start with preload first, get that right, then move to rebound. If you’re on a track that’s more slippery than usual (like a muddy track or a track with loose sand), you might want to soften your rear rebound a little—slower rebound keeps the tire planted to the loose surface, instead of bouncing over it. For hard, grippy tracks, faster rebound helps the bike turn sharper because the rear end can reposition quickly.
Let’s also cover a few pro tips I’ve learned from working with amateur and pro riders over the years. First, always check your shock’s linkage. The rear suspension on a dirt bike is connected to the frame via a linkage that translates the swingarm’s movement into shock movement. If your linkage has dirt or grease buildup, or if the bearings are worn, that will throw off all your adjustments. We stock premium linkage kits for all major Racing Dirt Bike models, and I’d recommend checking your linkage every 5 rides to make sure it’s smooth— a worn linkage can make a good shock feel bad, and a bad shock feel unmanageable.
Second, if you’re racing in varying conditions (one day the track is soft, the next it’s hard), keep a log of your settings. Write down your preload, rebound, spring rate, and track conditions every time you ride. After a few races, you’ll start to see patterns: when the track is wet and slippery, you run 12 clicks of rebound; when it’s dry and hard, you run 7 clicks. That log will save you hours of testing at the start of each race weekend.
Third, don’t ignore your sag. Wait, we mentioned sag earlier—sag is the amount the suspension compresses when you’re standing on the bike. Wait, no, let’s clarify: static sag is the compression when you’re sitting on the bike, rider sag is the compression when you’re leaning into a turn, and dynamic sag is the compression when you’re hitting a bump. Most riders focus on static sag, but rider sag is equally important. To measure rider sag, mark the swingarm at rest, then get on the bike, lean into your normal riding posture, and have a friend mark it again. The difference between static sag and rider sag should be 10 to 15 percent of your total rear travel. If rider sag is too low (meaning the rear is staying too high when you lean in), your bike will feel twitchy and hard to corner. If it’s too high, the rear will wallow in turns and lose traction. Adjusting rebound will change rider sag a little, which is another reason to get preload right first.
Now, when do you need to replace your rear spring? If you’re a consistent rider, and you’ve tried multiple preload settings and can’t get your static sag to 20-30 percent, that’s a sign your spring is the wrong rate for your weight. For example, if you’re 170 pounds, a standard 5.1 N/m spring might be too soft, and you’ll need a 5.4 N/m spring. We offer custom spring rates for all Racing Dirt Bike models, so you don’t have to stick to the stock setup that works for a 150-pound average rider. That’s one of the biggest advantages of working with a specialized supplier—we don’t sell one-size-fits-all parts, because we know every rider is different.
Let’s test this with a real example. Last month, a 165-pound amateur motocross racer came to me, complaining that his 2023 Racing Dirt Bike felt like it was bottoming out on triple jumps, and he was getting bucked on the whoops. He had cranked preload all the way up to the top of the adjuster, but his static sag was only 15 percent—way too low. We swapped his stock 5.0 N/m spring for a 5.2 N/m spring, set preload to get his static sag to 25 percent, then adjusted rebound to 7 clicks out from full slow. After testing, he said the difference was night and day: he wasn’t bottoming out anymore, the whoops felt smooth, and he gained 0.3 seconds per lap in his first race. That’s the power of a correct rear suspension setup—small changes, big results.
Now, let’s talk about common mistakes to avoid. First, don’t adjust compression damping on the rear. Some riders see a compression adjuster on the shock and start twisting it, thinking it’s the same as rebound. Compression damping controls how fast the shock compresses, which is for big hits like landings. Most modern Racing Dirt Bikes have rear compression adjusters, but they’re set at the factory for most riders, and adjusting them without knowing what you’re doing can lead to harsh rides or bottoming out. Stick to preload and rebound first, and only touch compression if you’re a more advanced rider with experience.
Second, don’t rush the test process. It’s tempting to set your suspension to what your friend uses, but every bike, every rider, every track is different. Your 200-pound friend might run 10 clicks of rebound, but you’re 130 pounds, so you need 12 clicks. We get this question all the time: “What do the pros run?” The answer is, it varies. A pro on a rough track will run slower rebound than a pro on a flat track, even if they weigh the same. So skip copying others, and do your own testing.
Third, don’t forget to break in your new shock or spring. If you’re installing a new shock spring, it’s going to be stiffer at first, and it will break in after 5 to 10 rides. So when you first install a new spring, adjust your preload a little looser than your final setting, and recheck your sag after a week of riding. That will save you from over-adjusting and ending up with a setup that’s too stiff once the spring breaks in.

At the end of the day, rear suspension adjustment is all about matching your bike to you and the track, not just following a number chart. As a Racing Dirt Bike supplier, we don’t just sell bikes and parts—we help riders get the most out of their machine, because we know that a well-tuned bike is faster, safer, and more fun to ride. If you’re tired of your bike feeling unpredictable, losing traction, or wearing you out after a race, or if you’re looking for custom parts to dial in your suspension for your specific riding style and track, reach out to us to talk through your setup. Whether you’re a weekend trail rider or a competitive racer, we can help you find the right adjustments and parts to get your bike handling exactly how you want.
Powerful Electric Moped References:
- Motocross Action Magazine. “The Ultimate Guide to Dirt Bike Suspension Tuning.” 2022.
- Off-Road.com. “Rear Suspension Basics for Racing Dirt Bikes.” 2021.
- Dunlop Motorcycle Tires. “Traction and Suspension: The Critical Link for Off-Road Performance.” 2023.
- Works Connection. “Factory Rebound Adjustment Tips for Motocross and Off-Road.” 2020.
Shandong Tuowei Locomotive Co., Ltd.
Shandong Tuowei Locomotive Co., Ltd. is one of the most professional racing dirt bike manufacturers and suppliers in China. With abundant experience, we warmly welcome you to wholesale high quality racing dirt bike at competitive price from our factory. If you have any enquiry about cooperation, please feel free to email us.
Address: No.7, Area E, Advanced Manufacturing Industrial City, Middle Section of Zizhou Avenue, Gaojia Community, Zichuan Economic Development Zone, Zibo City, Shandong Province, P.R.China
E-mail: sales@torvexmoto.com
WebSite: https://www.torvexmoto.com/