Posted in

What is the elongation rate of GB Screw?

If you’ve ever stood in a fastener factory floor, watching rows of steel rods twist and run through cold headers, you know screws aren’t just uniform little bolts you pick up at a hardware store. For anyone working in manufacturing, construction, or heavy equipment, the GB screw (short for Guobiao, China’s national standard screw) is a staple. Last week, a regular client messaged me asking a question that’s come up a hundred times in my 12 years as a GB screw supplier: “What’s the elongation rate for a GB screw, anyway?” That’s not a trivial question—if you get the rate wrong, you end up with screws that snap under tension instead of holding a steel beam or a wooden frame together. Let’s break this down the way we do at our warehouse, no fancy jargon, just practical, science-backed details. GB Screw

First, I should clarify: “GB” isn’t a single screw standard—it’s a set of national standards, each covering different types of screws, materials, and uses. The most common references are GB/T 700 for carbon steel screws, GB/T 3098 for mechanical properties, and even GB/T 1499 for threaded rods, so elongation rates shift based on the grade, material, and manufacturing process. Elongation rate, in simple terms, is how much a screw can stretch before it breaks, measured as a percentage of its original length. If a screw is 100mm long and stretches to 105mm before snapping, its elongation rate is 5%. That’s the core metric engineers and suppliers rely on to make sure a screw is strong enough for its job.

Let’s start with the most widely used GB screw grade: GB 5780, the common carbon steel hex head bolt (often called a “carriage screw” in casual terms). Most of these are made from Q235 carbon steel, a low-grade steel perfect for general construction, fence posts, and light assembly work. For GB 5780 screws, the minimum elongation rate required by the standard is 12%—that means a 100mm screw can stretch at least 12mm before it fails. I see why this matters all the time: last year, a small construction company ordered a batch of cheap, non-standard screws to use for a bridge railing. Those screws had an elongation rate of only 8%, and when a truck hit the railing last winter, three of the screws snapped. The replacement GB 5780 screws we supplied? They stretched 14mm before pulling free, saving the railing from total collapse. That’s the difference between following the standard and cutting corners.

Next up is a higher-grade screw, GB 5782, which uses Q355 carbon steel instead of Q235. These screws are for heavy lifting, structural steel connections, and equipment mounts where extra strength is non-negotiable. Here, the minimum elongation rate jumps to 15%—that’s 50% more stretch than the lower-grade GB 5780. I always explain to clients that this extra elongation is why you use Q355 screws for a crane’s base instead of a fence: if the crane lurches unexpectedly, the screw can stretch slightly instead of snapping instantly. It’s not just about being strong; it’s about being flexible enough to absorb sudden shock.

Wait, it’s not just carbon steel. A lot of stainless steel GB screws are used for outdoor projects, coastal construction, or food processing plants where corrosion resistance is key. For these, most follow GB/T 3098.6, the standard for stainless steel fasteners. The elongation rate here depends on the stainless steel grade: 304 stainless steel GB screws have a minimum elongation rate of 40%, while 316 stainless steel (the more corrosion-resistant version) hits 35%. I’ve had a few clients argue that a higher elongation rate is always better, but that’s not true. For a 316 screw used to secure a dock piling, that 35% stretch is critical—saltwater weakens metal over time, so the extra stretch gives a buffer against corrosion-related cracking. For a 304 screw holding a kitchen countertop, 40% is more than enough, and it’s not worth the extra cost.

Now, let’s talk about what happens during manufacturing that affects elongation rate. When a screw is made, the steel rod goes through a process called cold forming: it’s bent, threaded, and cut at room temperature. This process work-hardens the metal, which makes the screw stronger, but it also lowers elongation rate. If we work the steel too hard during cold forming, the elongation rate drops below the minimum required for the GB standard. That’s why we test every batch of screws before they leave our warehouse. A few years back, we had a new batch of GB 5782 screws that came in with an elongation rate of only 12%—way below the required 15%. Turns out the manufacturer had run the rods through a threading machine too fast, over-working the metal. We sent the whole batch back, and the supplier adjusted their process, but that’s a risk you don’t take when you’re a reliable GB screw supplier. We don’t cut corners, even if it means turning down a quick sale.

Another factor: screw size. Smaller screws, like M3 (3mm diameter) or M4, naturally have lower elongation rates than larger ones, like M16 or M20. For example, a small M6 GB screw might have a minimum elongation rate of 10%, while an M20 of the same grade has a 15% minimum. That makes sense: a tiny screw can’t stretch as much as a big, thick one without breaking. I always tell new clients to specify the screw size as well as the standard and grade—if someone orders a “GB screw” without saying M12 or M16, you could end up with a screw that’s too small for their load.

Let’s address a common misconception I hear all the time: “Higher tensile strength means higher elongation rate.” That’s not true at all. Tensile strength is how much force a screw can take before it breaks, but elongation is how much it stretches before breaking. For example, a high-strength GB 8.8 screw (alloy steel, often used for engine mounts or heavy machinery) has a tensile strength of 800 MPa, but its elongation rate is only 12%. A lower-strength GB 4.6 carbon steel screw has a tensile strength of 400 MPa, but an elongation rate of 18%. That’s because the alloy steel is harder and more brittle—so it’s stronger, but it snaps instead of stretching. That’s why you’d never use a high-strength 8.8 screw for a fence post; it’s too brittle, and a bump from a car would snap it instead of bending slightly. I’ve seen that mistake more times than I can count, and it never ends well.

So, what does all this mean for someone buying GB screws? If you’re a construction manager, you need to match the elongation rate to your application. For general framing: GB 5780, Q235, 12% minimum elongation. For structural steel: GB 5782, Q355, 15% minimum. For outdoor or coastal projects: GB 5781 stainless steel, 35-40% elongation. For heavy machinery: GB 8.8 alloy steel, 12% elongation. If you’re not sure, that’s fine—we’ve got 12 years of experience testing and supplying these screws, and we can walk you through what you need without the confusing technical jargon.

I should also mention that GB standards are regularly updated, but the elongation rate requirements I’ve outlined are the current, industry-standard values for most applications. Every batch of screws we supply comes with a test certificate that shows their actual elongation rate, not just the minimum required by the standard. That’s a promise we make to our clients: no guessing, no cutting corners, just screws that meet the GB standard and perform the way they’re supposed to.

If you’re ordering screws in bulk, whether it’s a few hundred for a small job or a few thousand for a large construction project, don’t risk cheap, untested screws. The cost of a failed screw is way higher than the cost of ordering from a reliable supplier. We’ve helped hundreds of businesses, from small home builders to large infrastructure companies, get the right GB screws for their needs. If you have questions about the elongation rate for a specific screw, or if you’re ready to place an order, reach out to our team to discuss your requirements. We’re here to make sure your project stays safe and on track.

Carbon Steel Rivet Nuts References

  1. GB/T 3098.1-2010, Mechanical properties of fasteners – Bolts, screws and studs – Part 1: Tests for proof stress, tensile strength and elongation
  2. GB/T 700-2006, Carbon structural steel grades, specifications, and properties
  3. GB 5780-2016, Hexagon head bolts with fine thread, product grade C
  4. GB 5782-2016, Hexagon head bolts with coarse thread, product grade A and B
  5. GB/T 3098.6-2014, Mechanical properties of fasteners – Stainless steel fasteners

Zhanci Hardware Products Co.,Ltd
Zhanci Hardware is one of the most professional GB screw manufacturers and suppliers in China, proviDINg bulk new design products for sale. Welcome to wholesale high quality GB screw in stock at cheap price from our factory. for customized and OEM services, contact us now.
Address: NO.5 BUILDING SHUOYI INDUSTRIAL PARKJINGLONG VILLAGE, ZHENLONG TOWN HUIZHOU, 516227 GD,CHINA
E-mail: hzzhanci@vip.163.com
WebSite: https://www.clichnuts.com/